EasyGel Protect®
drilling | Perforation with EGP250 or EGP500
Drilling | Perforation with EGP50VH
Home > Flow Control Products > EasyGel > EGP Drilling
Easy gel protect® Drilling
BCL INVENT® manufactures and markets a range of patented products, EasyGel Protect®, allowing capture and retention at source of fine and ultrafine particles.
The use of EasyGel Protect® solutions allow to reduce dust levels below the limit value for occupational exposure asbestos which is 10 fibers per liter for eight work hours.
These results are obtained in strict compliance with the implementation of our products.
Disclaimer:
Users are responsible for determining the suitability of the product for their intended use and for ensuring compliance with all applicable laws, regulations and local authority requirements. Users should review all relevant technical and safety information prior to use. Product information has been supplied by the manufacturer, EasyGel Protect BTP. While Derwent Industries Pty Ltd (Derwent) has taken reasonable care in making this information available, Derwent does not warrant its accuracy, completeness or suitability for any particular purpose. To the maximum extent permitted by law, Derwent disclaims all liability arising from reliance on this information or from the use, handling or disposal of the product and associated waste materials
| CODE | DESTINATION | DIAMETER | ADHESIVE | TYPE OF SURFACE |
|---|---|---|---|---|
| EGP100 | Drilling | Ø≤ 8 mm | Surface adhesive | Smooth |
| EGP100+ | Drilling | Glue ring | Rough | Smooth |
| EGP250 | Drilling | Surface adhesive | Smooth | Smooth |
| EGP250+ | Drilling | Ø≤ 14 mm | Glue ring | Rough |
| EGP500 | Drilling | Surface adhesive | Smooth | Rough |
| EGP500+ | Drilling | Ø≤ 16 mm | Glue ring Rough | Rough |
| EGP250 (or EGP500) and EGP50RECEP | Piercing | Surface adhesive / Receptacle without adhesive | Smooth | Rough |
| EGP250+ (or EGP500+) and EGP50RECEP | Piercing | Ø≤ 14 mm (or Ø≤ 16 mm) | Glue ring / Receptacle without adhesive | Rough |
EGP100 and EGP100+
Drill hole diameter Ø ≤ 8 mm
EGP250 and EGP250+
Drill hole diameter Ø ≤ 14 mm
EGP500 and EGP500+
Drill hole diameter Ø ≤ 16 mm
Standard adhesive
Smooth and delicate surfaces
High-tack adhesive (+)
Unevenand non-fragile surfaces
EGPSOL - Floor Use Only
Drill hole diameter Ø ≤ 10 mm
For each size, there are two sticker options
Adhesive-Free for floor use only
EGP drill bits, short fluted
Sizes Include:
FAEGP10 – 10 mm | FAEGP8 – 8 mm | FAEGP6 – 6 mm
- Improves sealing when drilling
- Reduces dust formation
- Visual depth indicator
Perforation with EGP250 or EGP500 :
Addition of a gel-filled container to be place at the exit point of the borehole
KITEGP50RECEP
(EGP50RECEP + 5L gel)
EGP50RECEP
Key Actions
- Make a mark, preferably in a colored ink, using a thick marker so that it is clearly visible through the EGP
- If you are using the “+” adhesive : Squeeze a small amount of gel into the center of the adhesive ring before bonding.
- Carefully pre-drill the manifold so as not to distort it.
- Move the gel back and forth in very steady strokes to mix the dust in thoroughly.
- Protect the floor beneath the drilling site, which will make it easier to clear up afterwards
Perforation with EGP50VH : Ø ≤ 25 mm
KITEGP50RECEP
(EGP50RECEP + 5L gel)
KITEGP50RECEP
Key Actions
- Make a mark, preferably in a colored ink, using
a thick marker so that it is clearly visible through the EGP. - Use a centre punch to mark the point on the other side of the wall.
- Pre-drill the joint using a drill bit with a smaller diameter than the main drill bit.
- Move the gel back and forth in very steady strokes to mix the dust in thoroughly.
- Protect the floor beneath the drilling site, which will make it easier to clear up afterwards.
EGP Core drilling :
Core drilling without water EGPCAR gel is heat-resistant and w ithstands high levels of dust generation The gel cools and lubricates the drill bit EGP core drilling tools are fully decontaminable and reusable
EGP150VH
Core drilling Ø ≤ 150 mm On walls and floors
EGP300V
Core drilling Ø ≤ 300 mm On the floor only
EGP50VH
Drilling Ø ≤ 25 mm Or Core drilling Ø ≤ 50 mm On walls and floors
Accessories included:
EGP50JOINT | EGP150JOINT
Drilling Silicone seal
EGP50RECEP | EGP150VH
Container
Stainless Steel Shovel
Pipe connection
EGPCS5CAR
4.75L flexible container of EGPCAR gel
EGPCS10CAR
10L flexible container of EGPCAR gel
EGPSG20CAR
20L bucket of EGPCAR gel
Key Actions
- Cut the seal to a diameter smaller
than that of the core bit - Ensure that the core bit remains submerged in the gel at all times
- Move the gel back and forth in very steady strokes to mix the dust in thoroughly
- Protect the floor beneath the drilling site, which will make it easier to clear up afterwards
