EasyGel Protect®
Home > Flow Control Products > EasyGel > EGB Cutting
Easy Gel Protect® Cutting
EasyGel Protect® products are designed to capture and retain fine and ultrafine hazardous particles at the source. They help reduce airborne asbestos dust thus protecting your team and the environment.
Disclaimer:
Users are responsible for determining the suitability of the product for their intended use and for ensuring compliance with all applicable laws, regulations and local authority requirements. Users should review all relevant technical and safety information prior to use. Product information has been supplied by the manufacturer, EasyGel Protect BTP. While Derwent Industries Pty Ltd (Derwent) has taken reasonable care in making this information available, Derwent does not warrant its accuracy, completeness or suitability for any particular purpose. To the maximum extent permitted by law, Derwent disclaims all liability arising from reliance on this information or from the use, handling or disposal of the product and associated waste materials
Capture and retention at source of fine and ultra-fine particles when cutting pipes, bars and tubes with a sabre saw.
- Performances
- When used in accordance with our recommendations (see instructions), EGP Découpes can be used to achieve dust levels below the occupational exposure limit of 10 fibres per litre of air.
- Printed LDPE sleeves with 3 longitudinal zones.
- The central zone contains the EGP gel.
- A dotted line marks the cut line along the entire length.
- The 2 lateral zones each contain a cable tie for fixing around a pipe or bar.
- Specially developed gel, suitable for contact with drinking water.
| CODE | APPLICATION | DIAMETER | LENGTH | SET |
|---|---|---|---|---|
| EGP32DEC | Pipes or bars | Ø ≤ 32 mm | 190 mm | - Pre-drilling EGP250 or an EGP500, depending on diameter (14mm or 16mm) - Spraying EGPIMP - Held in place by 2 cable ties |
| EGP50DEC | Pipes or bars | Ø ≤ 50 mm | 300 mm | |
| EGP125DEC | Pipes | Ø ≤ 125 mm | 650 mm | |
| EGP180DEC | Pipes | Ø ≤ 180 mm | 850 mm | |
| EGP250DEC | Pipes | Ø ≤ 250 mm | 1000 mm | |
| EGP300DEC | Pipes | Ø ≤ 300 mm | 1150 mm | |
| EGP400DEC | Pipes | Ø ≤ 400 mm | 1500 mm |
EGP Cutting
- EGP3DEC
- For cutting Ø outside diameter ≤ 32 mm
- Length x width : 220 x 125 mm
- Useful length : 180 mm ± 5 mm
- Total weight : 165 ± 5 g
- EGP50DEC
- For cutting Ø outside diameter ≤ 50 mm
- Length x width : 350 x 125 mm
- Useful length : 300 mm ± 5 mm
- Total weight : 245 ± 5 g
- EGP125DEC
- For cutting Ø outside diameter ≤ 125 mm
- Length x width : 650 x 125 mm
- Useful length : 600 mm ± 5 mm
- Total weight : 520 ± 5 g
- EGP180DEC
- For cutting Ø outside diameter ≤ 180 mm
- Length x width : 850 x 125 mm
- Useful length : 800 mm ± 5 mm
- Total weight : 660 ± 5 g
- EGP250DEC
- For cutting Ø outside diameter ≤ 250 mm
- Length x width : 1000 x 125 mm
- Useful length : 950 mm ± 5 mm
- Total weight : 780 ± 5 g
- EGP300DEC
- For cutting Ø outside diameter ≤ 300 mm
- Length x width : 1200 x 125 mm
- Useful length : 1150 mm ± 5 mm
- Total weight : 1050 ± 5 g
- EGP400DEC
- For cutting Ø outside diameter ≤ 400 mm
- Length x width : 1530 x 125 mm
- Useful length : 1500 mm ± 5 mm
- Total weight : 1880 ± 5 g
Adjustable to the diameter
| Code | Application | Range of Use | Set Up | |
|---|---|---|---|---|
| EGP32DEC : | Pipes of bars | Ø ≤ 32 mm | Held in place by 2 cable ties | Side cable clamps Gel suitable for contact with drinking water |
| EGP50DEC : | Pipes of bars | Ø ≤ 50 mm | Held in place by 2 cable ties | |
| EGP125DEC : | Pipes | Ø ≤ 125 mm | Held in place by 2 cable ties | |
| EGP180DEC : | Pipes | Ø ≤ 180 mm | Held in place by 2 cable ties | |
| EGP250DEC : | Pipes | Ø ≤ 250 mm | Held in place by 2 cable ties | |
| EGP300DEC : | Pipes | Ø ≤ 300 mm | - Pre drilling EGP250 - Spraying EGPIMP - Held in place by 2 cable ties | |
| EGP400DEC : | Pipes | Ø ≤ 400 mm | ||
| The gel in the EGPDEC-IS range has been specially adapted to capture the dust produced when cutting thick insulationa round pipes. | ||||
Key actions
- If there is a risk of dust being released due to vibrations, spray the surface of the pipe with impregnation gel (EGP IMP)
- Pre-drill the pipe using an EGP250 or EGP500 to allow the reciprocating saw blade to be inserted
- Ensure that the reciprocating saw blade remains within the gel at all times
- Do not press the reciprocating saw’s shoe against the EGP gel sheath
- If the pipe wall is thick, spray impregnation gel onto the blade throughout the cutting process
EGP Sawing
Adjustable to the diameter
| EGP022SCI : 200 mm | Adhesive underside Sawing plaster, concrete, chrome, ceramics… Reduces dust and minimises sparks |
| EGP035SCI : 300 mm | |
| EGP1SCI : 1000 mm | |
| EGP2SCI : 2000 mm |
Key actions
- Ensure that the core bit remains submerged
in the gel at all times - For power tools such as angle grinders or circular saws, reduce the speed to a maximum of 4,000 rpm
- Do not crush the EGP gel sleeve with the tool
